Build your own Ethereum Mining Rig, part 3: Windows Setup

Ethereum & WindowsNo doubt some of you saw the Ethereum mining guide for Linux that I published last week and balked at all of that “command-line nonsense”. Linux isn’t everyone’s thing, and that’s ok—if Windows is your OS of choice, then this guide is for you!

While Linux offers some significant advantages when it comes to GPU mining, Windows does have one potentially important edge: undervolting your GPUs currently requires quite a bit less effort under Windows. If you want your mining rig to run at its maximum efficiency, you’ll want to keep power consumption to a minimum, and with Linux that generally requires flashing a custom BIOS to each GPU—whereas in Windows you can usually accomplish this at the driver level with a simple software setting.

The bad news is that if you want maximum performance out of your rig, you’ll probably eventually want to flash your GPU BIOS under either operating system, but we’ll get into that in part 4 of this guide. But if you already know that overwriting your GPU BIOS with a custom replacement is outside of your comfort zone, then sticking with Windows will at least allow you to undervolt.

So with all of that in mind, if Windows sounds like the best option for you, read on for our setup guide!

Build an Ethereum Mining Rig, part 3: Windows Setup

I won’t go into quite the same excruciating level of detail as I did with my Linux guide, as it’s probably a safe assumption that anyone reading a guide about building a custom cryptocurrency mining rig is already quite comfortable with basic Windows tasks. The steps outlined below should be more than adequate for the average Windows user, but feel free to leave comments if anything is unclear!

Step 1: Configure BIOS Settings

Before we even get to Windows, make sure your mining computer’s BIOS settings are in order. Power on your computer, and press the “delete” key a few times immediately after power on. You should end up in the BIOS configuration area. Do the following, then save & exit:

  • Change power options so that the computer automatically turns itself on whenever power is restored. The reason for this is two-fold: first, it’ll make sure that your miner automatically starts up after a power outage. Second, it makes powering the computer on much easier if you don’t happen to have a power switch connected to the motherboard.
  • Disable all components that you don’t plan to use. This might save a little bit of power, and since your miner will likely be running 24/7, it’ll add up. For me, that meant disabling onboard audio, the USB 3.0 ports, one of the SATA controllers, the Firewire port, and the serial port.
  • If you’re running a lot of GPUs (4+), additional tweaks might be necessary to ensure that they’re all recognized by the OS. Exact tweaks vary by motherboard, but setting the PCIe speed to Gen1 is usually a good place to start. No need to change anything now, but make a mental note that you may need to come back and play around a bit if all of your GPUs don’t show up in the OS later.

Step 2: Install Windows 10

Any 64-bit edition of Windows 10 should work fine (a 32-bit OS is not capable of running the Ethereum mining software). Windows 7 and 8 will work as well (as long as they’re 64-bit versions), although you may need to do a bit of extra work to recognize all of your GPUs if you’re running more than 4. The guide is written assuming that you have Windows 10, but the steps for 7/8 should be pretty similar.

I’m going to assume that everyone reading this is capable of installing a fresh copy of Windows. Complete the installation and boot into the Windows desktop before proceeding to the next step. If necessary, also install the LAN/Ethernet driver that came with your motherboard so that you can get online.

Step 3: Configure automatic login

If you’re building a dedicated mining rig, then you probably want your mining rig to boot up and start mining automatically, without any user intervention. We’ll need to enable auto-login for that to be possible.

  • Right-click on the Start Menu and select “Run”. Type “netplwiz” (without the quotes) at the prompt, and click “ok”.
  • Uncheck the box that says “Users must enter a user name and password to use this computer”.
  • Click “Apply”. You’ll be prompted to enter your password to confirm the change.

Step 4: Change power settings to prevent sleep

By default, Windows will go to sleep after 30 minutes without user interaction. Obviously, we don’t want that behavior on our mining rigs. To disable it:

  • Right-click the Start Menu -> Control Panel -> System & Security -> Power Options.
  • “Balanced” should be selected. Click on “Change plan settings” next to it.
  • Change “Put the computer to sleep” to “Never”, then click “Save changes”.

Step 5: Minimize unscheduled reboots due to Windows Updates

Windows 10 introduced forced updates as a pretty controversial “feature”, and not having control over when your mining rig is rebooted to install OS patches could be frustrating. We’ll be setting things up so that your mining rig automatically begins mining any time Windows boots, so leaving automatic updates in place certainly wouldn’t be disastrous if you want to skip this section. But if you’d prefer to retain control over downtime, here are some workarounds:

Keep in mind that if this is a fresh install of Windows, it’s a good idea to let the OS install any available updates first (right-click start -> settings -> windows update -> check for updates).

Step 6: Allocate at least 16GB of virtual memory

The author of the mining software that we’ll be using recommends this step, although I’ve never encountered issues with a smaller pagefile (edit 4/19/17: I tried mining on a machine with only 4GB of physical RAM and got terrible performance until I increased my pagefile to 16GB). Here’s what you need to do:

  • Right-click the Start Menu -> System -> click “change settings” on the right side of the window (if you don’t see “change settings”, click “system info” first)
  • Click on the “Advanced” tab, then in the “Performance” area, click “Settings”
  • Click the “Advanced” tab, then click “Change” in the area labeled “Virtual Memory”
  • Uncheck the box at the top that says “Automatically manage paging file size for all drives”, then click on the “Custom Size” radio button.
  • Enter “16384” (without the quotes) in both the Initial and Maximum size fields, then click “Set”. You’ll need to reboot for the change to take effect.

Step 7: Disable unnecessary Windows visual effects

On systems with borderline hardware, this may increase performance a bit and help keep the OS a bit more responsive during mining:

  • Right-click the Start Menu -> System -> click “change settings” on the right side of the window (if you don’t see “change settings”, click “system info” first)
  • Click on the “Advanced” tab, then in the “Performance” area, click “Settings”
  • On the “Visual Effects” tab (which should be open by default), click on the radio button labeled “Adjust for best performance”, then click “Apply”

Step 8: Install AMD GPU drivers

AMD offers special mining-specific “blockchain compute” drivers that deliver considerably more performance than their standard drivers, so that’s what we’ll be using. If the computer that you’re installing to will not be a dedicated mining rig (eg: you plan to also play games on it, etc), you may prefer to use the latest available standard driver.

It’s ok to simply pick all of the default options during installation. Skip including ReLive when asked, as we don’t need it.

Reboot after the driver installation is complete.

Step 9: Generate a wallet address

You can skip this section if you already have an Ethereum wallet address. Otherwise, you’ll need to create one to mine with. There are many ways to generate your own wallet address, but I’ll show you how to do it using the official open-source Ethereum software. Be wary about trusting other methods, as some online creation tools are potentially scams designed to later steal your coins.

  • Download the latest release of Geth for Windows here.
  • When the download is finished, run the installer and select all of the default options.
  • Open a command prompt window (right-click the Start Menu -> Command Prompt).
  • Type the following to switch to the Geth installation directory (assuming you installed it in the default location):
    cd \Program Files\Geth
  • Type the following to create a new wallet address:
    geth account new

If you see a warning about starting the Ledger hub here, you can ignore it. You’ll be prompted to enter a password, and then to confirm it (use a strong password that you won’t forget!). The output will be a long string between two curly braces { }. That’s your new wallet address—make a note of it. You can easily copy it by right-clicking anywhere in the command prompt window, selecting “Mark”, highlighting your new address by holding left-click and dragging the mouse over the entire address, and then right-clicking again to copy to your clipboard. From there, you can paste your address anywhere using standard Windows shortcuts (CTRL+V).

Important: The combination of the password you just used to create this address *and* the associated encrypted key file is what gives you control over your new wallet address. If you lose either of these, you’ve also lost control of your wallet and all of the coins associated with it—and there is literally nothing that anyone will be able to do to help you. Remember your password, and keep multiple backups of your key file(s)!

Your key file(s) are stored in the %APPDATA%\Ethereum directory. For a fresh Windows 10 install, that means the C:\Users\[YOUR WINDOWS USERNAME]\AppData\Roaming\Ethereum\keystore folder (note that the AppData folder is hidden by default). Copy the entire keystore folder someplace safe to backup your wallet.

If you ever forget your wallet address, you can open a command prompt, return to your Geth installation folder, and type geth account list to see your addresses and the location of their key files.

Step 10: Install Claymore’s Ethereum miner

I talked about my reasons for selecting Claymore’s miner over other alternatives in my Linux guide, but to sum up: it’s currently the fastest, most stable Ethereum miner that’s still under active development. The downside is that it’s not free—about 1% of your mining time will benefit the creator of the software instead of you. However, even after the usage fee, you’ll come out ahead compared to the alternatives.

  • Download the latest version of Claymore’s ETH miner (v10.2 at the time of this post). Make sure to get the .zip file and not the Linux tar (also check here for newer releases)!
  • Extract the downloaded archive into a folder on your mining computer.
  • Open the folder where you extracted the miner, and create a new text file called “mine.bat” (you can use notepad for this).
  • Enter the following text into your mine.bat file exactly as written (but do make sure to substitute your own wallet address—see note below):
    timeout /t 15
    setx GPU_FORCE_64BIT_PTR 0
    setx GPU_MAX_HEAP_SIZE 100
    ethdcrminer64.exe -epool -ewal YOUR_WALLET_ADDRESS/Miner01 -epsw x -mode 1 -allpools 1


Where it says YOUR_WALLET_ADDRESS, use the address you created in step 9 (you’ll need to put “0x” in front of it). The “Miner01” following your address can be changed to any friendly label that you want to give your miner (only important if you plan to run multiple rigs).

Note that I’m using as the mining pool here. It’s a fairly typical ETH pool that seems to have good reliability, but feel free to pick your own pool. Most don’t require registration, and simply payout to whatever wallet address you supply whenever a certain threshold is met (usually whenever you accumulate 1+ ETH). Assuming you stick with Nanopool, you’ll be able to check on your miner’s status by going to this URL after you start mining:[YOUR WALLET ADDRESS]

Save and close notepad when you’re done.

Now is a good time to perform a quick test. Simply double-click your mine.bat file to launch the miner. It’ll take a minute or two before it actually starts mining, but it should get there eventually. When you see a scrolling log of outputs that includes non-zero hashrates (expect hashrates in the low to mid 20s for unoptimized GPUs), you’re good to go. If the script fails to start, or you see errors, make sure that you’ve created the script exactly as outlined in the guide.

Press CTRL+C to exit the miner when you’re satisfied that it’s working.

Step 11: Configure your miner to start automatically

We want our rig to automatically start mining whenever it’s powered on or rebooted. That way, we keep mining losses to a minimum whenever a power outage occurs, and we don’t have to worry about manually starting it back up in other situations.

  • Open Windows Explorer and navigate to the folder where you created “mine.bat” in the previous step.
  • Right-click on your mine.bat file, and pick “Copy”.
  • Now, navigate to %AppData%\Microsoft\Windows\Start Menu\Programs\Startup (should be something like C:\Users\[YOUR WINDOWS USERNAME]\AppData\Roaming\Microsoft\Windows\Start Menu\Programs\Startup).
  • Right-click anywhere on the empty background of the Startup folder and select “Paste shortcut”.

You should see a shortcut to your mine.bat file appear in the startup folder. Windows should automatically execute it upon bootup.

At this point, we’re done with the essentials. If you’ve done everything correctly, you should be able to reboot and watch your rig automatically start mining shortly after the Windows desktop loads. There are a couple more steps that may be important to you, though.

Step 12 (optional): Optimize clock speeds and undervolt (basic)

We’ll get into more advanced optimization in the next section of this guide, but as long as we’re on Windows, it doesn’t hurt to see what we can accomplish via some basic driver setting adjustments. We should be able to squeeze out some extra performance on most RX 470/480 cards and save a bit of power without venturing into the realm of BIOS mods.

  • Open the Radeon Settings app. There should be an icon for it in your system tray. If not, it’s located here: C:\Program Files\AMD\CNext\CNext\RadeonSettings.exe
  • Click on the “Gaming” tab at the top left.
  • Click on the “Add” button near the top right, then click “Browse”.
  • Navigate to the folder where you installed Claymore’s miner, select “EthDcrMiner64.exe”, and then click “Open”.
  • You should see a new profile appear on the Radeon Settings App window labeled “EthDcrMiner64”. Go ahead and click it.
  • Click on the “Profile OverDrive” tab.
AMD's WattMan

(click for full-size)

You should see something that looks like the image on the left (click for full-size). I’ve cropped in on the two areas that we’re interested in (they’re labeled “GPU” and “Memory”). Find them and start by setting the Frequency to “Dynamic” and the Voltage Control to “Manual” in both areas.

Before we go any further, I’ll just throw out this disclaimer: changing the factory voltage settings on your GPU can result in system instability, crashes, and/or damage. Proceed at your own risk! Honestly, the risk here is tiny—we’re still constrained to basically safe values by AMD’s software, and in the case of a crash we’ll just reboot and be back to factory settings (where we can try again with less-aggressive values).

We’re aiming to accomplish three things here:

  1. We want to lower the core clock speed as low as possible without impacting performance.
  2. We want to increase the memory clock speed as high as possible without impacting stability.
  3. We want to lower both the core and memory voltage as low as possible without impacting stability.

Before we go changing any values, if you haven’t run your miner at stock settings already for a few minutes to get a decent idea of its baseline performance, now is a good time to do that. Look for output along the lines of “ETH: GPU0 XX.XXX Mh/s” while Claymore’s miner is running. There will be some variance from line to line, but that XX.XXX number is the hash rate for that individual GPU. When you have a good idea of your average hash rate, close the miner—it’s time to start making some changes!

  • Start by decreasing your core clock speed to 1000 mhz from whatever the factory setting was (in the “GPU” area, change the values for state 6 and 7 to 1000 on the Frequency row). Click “Apply” (at the top right). Restart your miner and see how performance looks. There is a good chance that it’s unchanged. If that’s the case, repeat the process, but decrease the core clock speed by another 50 mhz or so. Keep moving down in 50 mhz increments until you notice mining performance drop. When that happens, bump the core clock back up to the previous value—that’s the sweet spot.
  • We’re going to basically do the reverse with the memory clock speed, but there are some important things to know. If you have a GPU that is factory-clocked at 1750 mhz or less (virtually every 4GB RX 470/480 GPU, and most RX 470 8GB GPUs as well—the Sapphire Nitro being the notable exception—then 1750 mhz is going to probably be your limit via this method. Increasing the memory clock beyond 1750 mhz will likely result in a change to less-aggressive memory timings that will result in a loss of performance, and there is no way to prevent this outside of BIOS modifications. So if you have a card clocked at under 1750 mhz, bump it up to exactly 1750 mhz, which will give you a decent performance boost. If you have a 2000 mhz card, you can increase it incrementally, like the reverse of what we did with the core clock. Eventually you’ll experience system instability: artifacts on the screen, a GPU crash, bluescreen, etc. When that happens, back down a bit until things are stable.
  • When you’re satisfied that you’ve found the sweet spot for both clock speeds, it’s time to lower voltages. This is pretty straightforward: drop values 25 mV at a time until you experience instability, then bump it back up to last stable value. You should be able to reduce your power consumption a fair bit this way without impacting performance at all (these are great if you want to measure your electricity usage at the wall).

While more significant performance gains are possible by flashing a custom GPU BIOS (which I’ll cover in the next part of this guide), you should at least be able to realize some significant power savings (which has the added benefit of lowering GPU temperatures as well).

The screenshot in this section is from a factory-clocked 1650 mhz 4GB RX 470 GPU. Feel free to use the settings pictured as your starting point if you have a 4GB GPU, I haven’t found any cards that aren’t stable at these settings yet; most go a bit lower on the voltages.

 Step 13 (optional): Configure remote administration

Configuring remote administration will allow you to disconnect the monitor, keyboard, and mouse from your mining rig and manage it from another computer—even over the internet, if you wish. Windows 10 Professional and up have the built-in option to use Remote Desktop, although it’s disabled by default and must be configured. It’s a fine option if you’re looking for something basic and don’t want to install additional software.

There are a host of other options available, if you’re on a Home edition of Windows and/or want something a bit more robust. I recommend TightVNC: it’s lightweight, simple, cross-platform, and free. Here are the basic setup instructions for TightVNC:

  • Download TightVNC.
  • Install TightVNC on your mining rig. Choose a custom installation and make only the server portion of the application available.
  • Now install TightVNC on the other computer(s) that you plan to manage your rig with. Choose a custom installation and make only the client portion of the application available.
  • If you plan to manage your miner across the internet, forward port 5900 on your router to your mining rig (make sure you choose a strong password if you do this!).

That’s it—you’re done! You’ll probably want to test everything now. The easiest way to do that is to power down your miner. Turn it back on and the following should happen:

  1. Windows should boot up as usual.
  2. You should see a 15 second countdown to the Claymore miner’s launch shortly after the Windows desktop appears.
  3. After the countdown, the miner will start, and your GPUs should start mining.
  4. You should be able to VNC into your rig at any point after the desktop loads to monitor your miner’s progress and GPU temperatures.
  5. If you ever need to start the Claymore miner manually (because you quit out of it, or it crashed, etc), simply double-click your mine.bat file, located in your Claymore miner installation folder.

Congratulations—you have your own headless windows Ethereum miner!

The screenshot above shows a single 4GB RX 470 mining at the settings pictured in section 12. I was able to get about a 10% performance gain over factory settings while reducing power consumption at the same time. That’s good, but we can do better (sometimes much better!) if we’re willing to venture into the world of GPU BIOS mods—and I’ll show you how to do exactly that in the next section of my guide.

323 Responses to Build your own Ethereum Mining Rig, part 3: Windows Setup

  1. Thomas Watcharawut Kuna Mogensen says:

    I have my rig up and running but only one of the Cards are detected by the pc and can mine, the other is connected via a pcie adapter.

    Anyone know how to solve this ?

    • david r says:

      make sure you run the atikmdag patcher program at least once if it says found run it if it says already fixed the it may take a few reboots

    • Saleh says:

      Check your motherboard bios. For me, The motherboard (Gigabyte) bios had an option “Mining mode”. When it is enabled the gpus will be detected. Other motherboards I read online have an option called “4G…” I don’t remember. you need it to be enabled.

  2. Saul says:

    This is a great guide, thanks for sharing your experience with us!

    I installed TightVNC on my mining rigs and for most part it works fine; however, I am unable to view Firefox and run .exe files (like DDU) from a remote machine. Is there any fix for that or do you recommend alternative VNC client which lets you do that? Or do I have to change any settings in TightVNC or Windows 10?

    Thanks a lot!

    • CryptoBadger says:

      I haven’t used TightVNC in a couple years, but anything that uses the GPU might not be rendered over a connection. Try disabling hardware acceleration in Firefox to see if that fixes the issue.

      TigerVNC is also highly regarded if you want to try a different product.

  3. darren says:

    ETH: Stratum – connecting to ‘’ port 14444
    ETH: Stratum – Connected (
    ETH: Share rejected!
    Socket was closed remotely (by pool)
    ETH: Job timeout, disconnect, retry in 20 sec…



    his pool ( does not support Ethereum addresses as login (or requires worker name in “Login.Worker” format) and cannot be used for devfee mining, therefore it is not supported.
    However, you can mine on this pool if you specify “-allpools 1” option, default pools (different from this pool) will be used for devfee.
    Please read “Readme” file for details.This pool ( does not support Ethereum addresses as login (or requires worker name in “Login.Worker” format) and cannot be used for devfee mining, therefore it is not supported.
    However, you can mine on this pool if you specify “-allpools 1” option, default pools (different from this pool) will be used for devfee.

  4. Junaid says:

    Why i’m getting Total share: 0????

  5. Dmytro says:

    Will there be any problems if I install fresh Windows 10 and AMD drivers on GPUs with already modded BIOS? In procedure described here Windows and AMD drivers are insrtalled when GPUs are with factory BIOS, isn’t it?

  6. rob says:

    dude…thank you so much. seriously.

  7. AKT says:

    Someone can teach me what are this commands “-mode 1 -tt 68 -allpools 1
    pause” in the “mine.bat”

    pause = don’t running?????!!!


    and a lot of thanks for this guide, really!!!!

  8. Deadre says:


    I’ve just built my rig:
    -Asrock h81 btc mb
    -4gb ram
    -intel celeron g1840 cpu
    -4x msi geforce gtx 1070 armor oc
    -evga supernova 1000

    I just started mining and the rig draws 1250watt from the wall, while i monitored my GPU-s and each used 130watt. Its just dont add it up and this is a lot of power to pay. Any idea? I use the claymore miner

    • FpsStang says:

      Ya that’s crazy. I’m running 6 1070s and only pulling 850-950 depending on men clock. Have u dropped the power % down? Dropped the core clock?

    • AussieBen says:

      That GPU power reading of 130w would be GPU core power draw only (gpuz reading). This doesn’t give you memory or fan power. I think this is where you getting your first power draw assumption wrong.

      Nvidia cards might be comparable to AMD cards for MH to power consumption out of the box however AMD cards can be undervolted far further then Nvidia cards can before crashing. From my old gaming OC experience and from what I’ve read online with Nvidia mining rigs, they arn’t the best performers. My 580 Nitros came out of the box at 23MH/s at nearly 200w draw at the wall each card. After overclocking memory, underclocking core and undervolting both, I’m now getting a stable 31MH/s at 125-130w at the wall per card. I highly doubt any Nvidia card can get that kind of stable change in efficiency.

      I’ve always used Nvidia for gaming, they are clearly the best. But with above said, plus the fact they are hugely more expensive upfront cost, AMD is the way to go for mining rigs.

  9. ben says:

    Hi Everyone,
    Finally getting my rig up and running but having trouble getting Claymore to work, its registering my card but getting this error all the time..server – bind failed with error 10048, port for remote management is busy..any ideas?

    • AussieBen says:

      More info. What cards? Are you using latest drivers?

      • ben says:

        I’m running a p106-100 or gtx1060, been to NVidia and got the latest driver, just getting:
        ETH Stratum – connecting to us1.ethermine, ord port4444
        ETH Stratum – cannot connect to us1.ethermine.ord4444
        ETH Stratum – Failed to connect – Retry in 20seconds

      • AussieBen says:

        I’d say a firewall or antivirus is blocking it. Need to allow connections for EthDcrMiner64.exe. Also, that address looks wrong. Double check your pool address in your .bat file is correct.

        • ben says:

          Hi Again,
          Sorted the problem, it was a problem with how the bat file was written, no trying to work out how to downclock/overclock the memory but cant work out how to access the gpu, on windows 10 I can find the gpu but not really do anything with it.

  10. Elmar says:


    is it possible o run 11 of the same model GPU’s on a Windows10 Rig?

  11. Robert T says:

    When I turn off the monitor, I get “Cannot get Overdrive capabilities” from Claymore when the AMD driver crashes. Does anyone have any ideas other than keeping my monitor turned on all the time, or buying a dummy plug?

  12. Ben says:

    Hi Everyone,
    Result – Just to let everyone my rig running with Claymore, and just hooked up a Colorful P106-100 to it. Stock MH/s were 19.5 but with MSI afterburner I can squeeze it up to borderline 24, 23.9 MH/s. No Bios mods or anything too extreme either. I can hit 24.5 but the gpu becomes unstable and crashes and resets..not good when you get a black screen and no response..

    • Robert T says:

      That’s very a good Mh/s. I get about 22, but I undervolt it to reduce power consumption. Where I live, we pay 20 cents per kwh, so the extra mhs is offset by the additional power cost.

  13. Arun Kumar says:

    Hi Cryptobadger,

    I assembled the following hardware with 6 GUPs, however the motherboard doesn’t supports more than 3 GPUs.

    Motherboard: Biostar TB250-BTC v6.0
    CPU: Intel Celeron
    RAM: 4GB corsair
    PSU: EVGA 1200 P2
    GPU: Sapphire Nitro+ RX580 8GB

    I have tried the following:
    – Updated the system BIOS
    – Installed old drivers for the PSU
    – Tried with latest drivers
    – Tried with mixed drivers
    – Changed the mining mode in BIOS
    – Tried the PCI mode to Gen1, Gen2 and Auto

    Reinstalled windows few time, but no luck. Any help will be highly appreciated.


    • Robert T says:

      try it under Linux. Biostar has problems-other people have also reported. There are also some BIOS settings that you may need to change. Google your motherboard and maybe someone already fixed it.

      • Arun Kumar says:


        Thanks for your response. I tried that and the motherboard is not even booting in Linux. It appears that the motherboard is faulty and will be returning it.

    • Ben says:

      Seems strange that a dedicated mining board with 6 pcie slots would have trouble recognising only three..doesnt make sense..I’d like to know if there is a problem, I’m running a Biostar TB250 (non V6) albeit with only one card and no issues, but mine is set to mining mode only.

      • Arun Kumar says:

        Yes Ben, it is strange and have wasted 2-3 days trying to fix this while trying different options. Finally, I have figured it out that the motherboard is faulty. FYI, I had a spare ASUS ROG STRIX Z270E GAMING motherboard (this is slightly expensive) and I switched the motherboards. With few settings in the ASUS BIOS it worked flawlessly. All the 6 GPUs recognized by the motherboard and no issue at all.

  14. john says:

    Is there anything to change fan speeds in linux claymore or something? i couldn’t find anything. Claymore fan speed monitoring is bogus

  15. Dave Yaffe says:

    Thank you so much for sharing this. First Eth rig (bitcoin up till now). Simple and thorough. Working fine right off the bat.

    I have one question. When I tried the other tutorials to get started, they all had me download the blockchain. After about 36 hours, I gave up and came here.

    My question is, how is the blockchain download happening HERE?

    Thanks in advance.


  16. Dave Yaffe says:

    Hi all, been using for about 8 hours so far (new setup). Using MyEtherWallet, checked and double checked that the wallet address is correct.

    At what point do you see transactions deposited in your wallet with this program? I know, with my Bitcoin, I can set a limit and deposits are made when I reach that limit of “reward”. What about here, with Ethereum using this program?

    Thanks in advance.

    • john says:

      have you joined a mining pool?

      You can get updates in 10 minutes or so once you make a valid share (shown in the mining software like claymore/genoil)

      You can then check on your miner stats on the pool website. Your reported/posted hashrate on claymore/etc doesn’t matter for the reward. All that matters is the calculated hashrate as posted on the mining pool website. Your payout is based on this calculated hashrate.

      eg. mining pool -> and check on any of the miners on that page to get the stats. You should see similar stats for yours when you enter your ETH wallet address (once you make a valid share)

  17. J says:

    Following this guide, and using Geth to create account and wallet, if changing motherboard, and needs reinstallation, what should I backup? Kindly advise, urgent. Changing from 6 pcie to 13 pcie board.

  18. J A says:

    Following instructions above”

    “Type the following to create a new wallet address:
    geth account new”

    Is this myetherwallet? or what kind of wallet did I create? Where can I check balance?

  19. Anonymous says:

    I have an Eth mining rig set up and running and last night I upgraded my GPU in my gaming computer. Because it’s a really nice GPU I decided that when I was wasn’t gaming, I’d use it to mine as an additional GPU. So, I basically copied and pasted my mining software, batch file etc. from my rig to my gamer, started it up and it worked like a champ. However, I noticed this AM that the “reported hash rate” on the etherminer pool is down to the hash power of my gamer, but my “Effective hash rate” is actually higher than it’s ever been AND I am reporting more shares per hour. So.. is everything ok?! Why would it only show my report rate from my single gpu, but appear to be recognizing the work of all of them?

  20. I am just an old guy trying new things. My question is, If I already have an ethereum wallet on coinbase, can I use that?

    • john says:

      Yes you can. However it’s not advisable for long term and also not advised by coinbase. I tried it for a temporary 0.11 ETH mining to test it out and it worked.

  21. CAMERON says:

    I have a question on your mining rig’s video card drivers do you need to only install the one card your screen works off or do you have to install all of your cards video drivers that you are using to mine with???

  22. MacAries says:

    in device manager you need to see all your installed cards and they all need their respective drivers

  23. JC says:

    Hi friends, I built my rig following the 95% of this instructions (the other 5% was tweaking the cards), after a month I want to cash out the ETH I have produced from the GETH wallet. My question : how do I transfer the balance from my GETH wallet to another wallet or person ?
    Kind regards

  24. Zelda says:

    I noticed sometimes Claymore would lose track of some or all GPUs for temperature/fan control under Windows. Carefully re-reading the release notes, Claymore suggests not using Remote Desktop, which was how I was accessing the rig. If I reboot from a directly connected monitor, or wait until Claymore is up and running before using RDP access, it seems to start the temp/fan feedback loop successfully.

  25. William says:

    @cryptobadger do u now recommend using the and beta mining driver or just the latest regular driver?

Leave a Reply

Your email address will not be published.